Instructions Memory Can Not Be Read Hard Drive

USB devices like Hard Drives, Pen drives, and Memory Card, etc. are the easy fashion to store and transfer information from one computer to another. These USB drives are portable and easy to handle, but sometimes you might face the Hard disk drive non detected a problem with Windows PC. This happen when the USB port did non recognize the external USB drives. When you try to admission the information from the hard drive or USB device, y'all run across the post-obit USB Device Not Recognized error message:

"One of the USB devices attached to this computer has malfunctioned, and Windows does not recognize it for aid in solving this trouble, click this message."

इस पोस्ट को हिंदी में पढ़ने के लिए यहां क्लिक करें।

Table of Content

• • How to fix External Hard Disk not Detected in Windows?
    • • • • Disconnect the power supply
          • Disconnect USB Device
          • Update USB device drivers
          • Change Bulldoze Alphabetic character
          • Set USB Root Hub
          • Change USB Selective Suspend Settings
  • Contact Data Recovery Service Provider
  • Unlike situations of  Hard disk take non detected errors

How to fix External Hard Disk not Detected in Windows?

Disconnect the ability supply

Sometimes, a very uncomplicated trick can ready an external hd non detecting a problem. Follow the below steps to apply this trick.

• Close Down your computer
• Disconnect the power cable from your figurer and await for a few minutes
• Reconnect the power cable and Start your computer.

Disconnect USB Device

• Disconnect the USB devices from your computer
• Restart your estimator
• Reconnect USB devices to your computer

[Annotation]: If the current USB port doesn't detect the difficult drive then, try to connect it with another USB port. If it is recognized by other USB ports so, there could exist a hardware problem with one of the USB ports. If no USB port recognizes the device then, try some other solution. Don't employ any USB hub to connect the device to the figurer.

Update USB Device Drivers

If all USB ports are working fine and then yous need to bank check for the latest USB commuter installed on the calculator. Because sometimes former drivers can prevent the drive to connect to the PC and shows the hard disk not detected an error. To cheque driver status follow the below steps.

• Printing Windows + R key together and then, blazon devmgmt.msc in the run dialogue box and click on OK.
• Expand disk drivers and correct-click on the connected external USB bulldoze.
• Click on backdrop and select the Driver tab.
• Click on Update Driver Software and follow the farther instruction to update the driver.

[NOTE]: if this method doesn't work, then download and install the updated USB drivers from the figurer manufacturer's website. This is useful in instance if you are trying to install a driver for a printer, scanner, and other input/output USB device.

Change Drive Letter

Check whether you lot can see your external USB Bulldoze in Disk Direction, then rename or change the drive letter of the alphabet. To exercise this follow the below steps.

1. Right-click on This PC or My Figurer and click on Manage.

ii. Select Disk Direction.

3. Right-click on the connected external bulldoze and choose Alter Bulldoze Letter and Paths.

4. Click Add, and then assign a new bulldoze alphabetic character from the driblet-down listing and click OK.

Set up USB Root Hub

• Press Windows + R key together and and then blazon devmgmt.msc and click on OK.
• Expand Universal Series Bus controllers.
• Correct-click on USB Root Hub and click Properties.
• Select Power Management and uncheck the Allow the calculator to turn off this device to relieve the ability checkbox. Click ok and save changes.

[Notation]: Repeat this process for all available USB Root Hubs. Save changes for each process and then restart your PC. If withal you meet a USB device not recognized problem then get back to the power management tab for each ane and check the box again.

Modify USB Selective Suspend Settings

1. Become to Control Panel and click on Hardware and Sound.

2. Click on Power Options.

3. Select Change Programme Settings under preferred plans. Counterbalanced (recommended).

iv. Click on Change advanced power settings.

5. Expand USB settings and USB selective suspend settings.

6. Select Disable from the drop-downwards menu.

7. Click "Utilize" and "OK" to save the settings.

[NOTE]: If you use the laptop, and then you'll run into ii options: On Battery and Plugged in. So, select disable for both settings respectively.

Contact Data Recovery Service Provider

If all the above-mentioned solutions don't fix the external hard drive non detect the trouble. And you are still getting the same error; then there are high chances that your difficult bulldoze has become expressionless. In this situation, you need to accept the help of a Professional Hard Drive Recovery service provider.

If your problem is resolved, and so information technology is brash that yous should take a fill-in of your hard bulldoze data; to avert any information loss in the time to come.

Different situations of  Hd have non detected errors

Difficult bulldoze not detected fault/result can be caused by the following situations:

• • The USB driver has become unstable, outdated, or corrupt
  • USB ports go faulty, damaged, or cleaved
  • Partition issues on your external USB device
  • The USB device is malfunctioned or damaged
  • The wrong file organization in an external bulldoze
  • Virus-infected PC

If the problem still persists after implementing the above steps and then possibility that your hard drive is severely corrupted or damaged. In that instance, you can approach a reliable data recovery service provider.

crockerharmal.blogspot.com

Source: https://www.stellarinfo.co.in/blog/how-to-fix-external-hard-disk-drive-not-recognized/

Share this post